# OFFSET shells and beams with a temperature gradient get wrong expanded-node temperatures: wrong thermal expansion, and beams bend (1 + 2·OFFSET) times as much

**URL:** <https://calculix.discourse.group/t/offset-shells-and-beams-with-a-temperature-gradient-get-wrong-expanded-node-temperatures-wrong-thermal-expansion-and-beams-bend-1-2-offset-times-as-much/4212>\
**Category:** Analysis issues\
**Created:** [October 21, 2026, 7:04pm UTC](https://calculix.discourse.group/t/offset-shells-and-beams-with-a-temperature-gradient-get-wrong-expanded-node-temperatures-wrong-thermal-expansion-and-beams-bend-1-2-offset-times-as-much/4212 "2026-10-21T19:04:08Z")\
**Posts on this page:** 3\
**Page:** 1

<div class="post-metadata">

**Author:** ![Sandervdb](https://avatars.discourse-cdn.com/v4/letter/s/49beb7/32.png) [@Sandervdb](https://calculix.discourse.group/u/Sandervdb)\
**Post date:** [October 21, 2026, 7:04pm UTC](https://calculix.discourse.group/t/offset-shells-and-beams-with-a-temperature-gradient-get-wrong-expanded-node-temperatures-wrong-thermal-expansion-and-beams-bend-1-2-offset-times-as-much/4212/1 "2026-10-21T19:04:08Z")

</div>

## Summary

The manual, \*TEMPERATURE (section 7.132 of the 2.23 manual): “For shell elements a temperature gradient can be defined in addition to a temperature. The temperature applies to nodes in the reference surface, the gradient acts in normal direction. For beam elements two gradients can be defined: one in 1-direction and one in 2-direction.” With `*SHELL SECTION, OFFSET=e` or `*BEAM SECTION, OFFSET1=e1, OFFSET2=e2` the reference surface (line) is not the mid-surface (axis). The expanded element’s nodes are placed accordingly, but gen3dtemp.f does not give them the matching temperatures. Exit 0, no warning.

**Shells.** The middle expanded nodes lie at a distance e t from the reference surface. gen3dtemp.f gives them the reference-surface temperature T, instead of T - g e t. The outer nodes are right. The temperature through the thickness is then no longer linear, and its mean is off by (2/3) g e t. So the in-plane thermal strain is off by (2/3) alpha g e t, for any T. The curvature is right. For T = 0 the expansion is 1/3 of the correct value, for other T the ratio differs.

**Beams** (SECTION=RECT checked). gen3dtemp.f uses the factor (0.5 + offset) on both sides of the section and leaves the offset out at the middle nodes. The expanded nodes on the positive side, and the middle nodes, get wrong temperatures. The temperature at the centroid becomes T instead of T - g b e (b the thickness in that direction), and the gradient becomes (1 + 2 e) g: twice the input for e = 0.5, zero for e = -0.5.

Test: pairs of decks that describe the same solid with the same temperature field. One uses the offset; its twin has the nodes at the mid-surface (centroid line) and gives the temperature there. The pairs should give the same displacements:

- S8R plate, OFFSET=0.5, T = 0, gradient 100: in-plane U1 = -3.333E-03, twin -1.000E-02. With T = 10: 1.667E-02, twin 1.000E-02. Both errors are (2/3) alpha g e t x = 6.667E-03. The bending (-0.1) is right.
- B32 cantilever, OFFSET2=0.5, T = 10, gradient 100 in the 2-direction: tip deflection -0.1000006, twin -0.05000029; axial 1.0E-02, twin 5.0E-03. With OFFSET2=-0.5 the beam does not bend at all.

## Version

ccx 2.23 (macOS arm64). Source: master 9ba5d76 (16 Oct 2026).

## Already reported or fixed?

Not reported: I found no matching GitHub issue (open or closed) or pull request in Dhondtguido/CalculiX, and no calculix.discourse.group topic (searched 21 Oct 2026). Not fixed: `gen3dtemp.f` is unchanged on master (9ba5d76).

## Minimal input

`offset_gradient.inp`: a flat 2 x 1 plate of two S8R elements (thickness 0.1, OFFSET=0.5, E 1000, nu 0, alpha 1E-3), supported statically determinate; T = 0 and gradient 100.

```auto
*NODE, NSET=NALL
1, 0, 0, 0.
2, 0.5, 0, 0.
3, 1, 0, 0.
4, 1.5, 0, 0.
5, 2, 0, 0.
6, 0, 0.5, 0.
7, 1, 0.5, 0.
8, 2, 0.5, 0.
9, 0, 1, 0.
10, 0.5, 1, 0.
11, 1, 1, 0.
12, 1.5, 1, 0.
13, 2, 1, 0.
*ELEMENT, TYPE=S8R, ELSET=EALL
1, 1, 3, 11, 9, 2, 7, 10, 6
2, 3, 5, 13, 11, 4, 8, 12, 7
*MATERIAL, NAME=M
*ELASTIC
1000., 0.
*EXPANSION
1.E-3
*SHELL SECTION, ELSET=EALL, MATERIAL=M, OFFSET=0.5
0.1
*BOUNDARY
1, 1, 3
3, 2, 3
9, 3, 3
*INITIAL CONDITIONS, TYPE=TEMPERATURE
NALL, 0.
*STEP
*STATIC
*TEMPERATURE
NALL, 0., 100.
*NODE PRINT, NSET=NALL
U
*END STEP

```

`midsurface_twin.inp`: the same solid without offset. The nodes move to mid-thickness, and the temperature line gives the mid-surface temperature T - g e t = -5:

```auto
--- offset_gradient.inp
+++ midsurface_twin.inp
@@ (all 13 nodes)
-1, 0, 0, 0.
+1, 0, 0, -0.05
 ...
-13, 2, 1, 0.
+13, 2, 1, -0.05
@@
-*SHELL SECTION, ELSET=EALL, MATERIAL=M, OFFSET=0.5
+*SHELL SECTION, ELSET=EALL, MATERIAL=M
@@
-NALL, 0., 100.
+NALL, -5., 100.

```

Both expand into the same C3D20R solid between z = -0.1 and z = 0, with T(z) = 100 z. The T = 10 pair uses `NALL, 10., 100.` and `NALL, 5., 100.`.

`beam_offset_gradient.inp`: a B32 cantilever along z (length 1, RECT 0.1 x 0.1, n1 = x, so n2 = y), clamped at z = 0, OFFSET2=0.5 (the reference line is the +y face), T = 10, gradient 100 in the 2-direction.

> **beam\_offset\_gradient.inp and its twin**
>
> ```auto
> *NODE, NSET=NALL
> 1, 0., 0., 0
> 2, 0., 0., 0.25
> 3, 0., 0., 0.5
> 4, 0., 0., 0.75
> 5, 0., 0., 1
> *ELEMENT, TYPE=B32, ELSET=EALL
> 1, 1, 2, 3
> 2, 3, 4, 5
> *MATERIAL, NAME=M
> *ELASTIC
> 1000., 0.
> *EXPANSION
> 1.E-3
> *BEAM SECTION, ELSET=EALL, MATERIAL=M, SECTION=RECT, OFFSET2=0.5
> 0.1, 0.1
> 1., 0., 0.
> *BOUNDARY
> 1, 1, 6
> *INITIAL CONDITIONS, TYPE=TEMPERATURE
> NALL, 0.
> *STEP
> *STATIC
> *TEMPERATURE
> NALL, 10., 100., 0.
> *NODE PRINT, NSET=NALL
> U
> *END STEP
> 
> ```
> 
> `beam_centroid_twin.inp`: the nodes on the centroid line (y = -0.05), no offset, and the centroid temperature T - g b e = 5:
> 
> ```auto
> --- beam_offset_gradient.inp
> +++ beam_centroid_twin.inp
> @@ (all 5 nodes)
> -1, 0., 0., 0
> +1, 0., -0.05, 0
> ...
> @@
> -*BEAM SECTION, ELSET=EALL, MATERIAL=M, SECTION=RECT, OFFSET2=0.5
> +*BEAM SECTION, ELSET=EALL, MATERIAL=M, SECTION=RECT
> @@
> -NALL, 10., 100., 0.
> +NALL, 5., 100., 0.
> 
> ```

Variants: OFFSET1=0.5 with the gradient in the 1-direction (`NALL, 10., 0., 100.`; twin at x = -0.05, `NALL, 5., 0., 100.`), and OFFSET2=-0.5 (twin at y = +0.05, `NALL, 15., 100., 0.`).

## How to run

```auto
ccx offset_gradient
ccx midsurface_twin
ccx beam_offset_gradient
ccx beam_centroid_twin

```

## Expected

The same displacements in each pair. Shell twin: the mid-surface temperature T\_mid = T - g e t gives the in-plane strain alpha T\_mid and the curvature alpha g = 0.1, so U1 = alpha T\_mid x and U3 = -0.1 at node 5 (x = 2, y = 0). Beam twin: curvature alpha g = 0.1, tip deflection alpha g L²/2 = 0.05, axial alpha (T - g b e) L = 5.0E-03. Both decks of a pair print the reference nodes as the average of the same expanded nodes, so the printed values must match too.

## Actual

Exit 0, no warning, in every run.

Shells, node 5 (x = 2), g = 100, t = 0.1:

| OFFSET e | T | U1 ccx | U1 expected (alpha T\_mid x) | U1 error | (2/3) alpha g e t x | U3 |
| --- | --- | --- | --- | --- | --- | --- |
| 0.5 (offset\_gradient) | 0 | -3.333333E-03 | -1.000000E-02 (twin) | +6.667E-03 | 6.667E-03 | -1.000000E-01 |
| 0.5 | 10 | 1.666667E-02 | 1.000000E-02 (twin) | +6.667E-03 | 6.667E-03 | -1.000000E-01 |
| 0.25 | 0 | -1.666667E-03 | -5.0E-03 | +3.333E-03 | 3.333E-03 | -1.000000E-01 |
| 0.25 | 10 | 1.833333E-02 | 1.5E-02 | +3.333E-03 | 3.333E-03 | -1.000000E-01 |
| -0.5 | 0 | 3.333333E-03 | 1.0E-02 | -6.667E-03 | -6.667E-03 | -1.000000E-01 |
| 0 | 0 | 4.8E-16 | 0 | 0 | 0 | -1.000000E-01 |

`offset_gradient.inp` with S8 instead of S8R: the same (-3.333334E-03). With a uniform temperature (`NALL, 100.`) and OFFSET=0.5, U1 is 0.2 = alpha T x, as expected.

Beams, tip node 5, T = 10, g = 100, b = 0.1:

| deck | bending deflection | twin | axial U3 | twin |
| --- | --- | --- | --- | --- |
| OFFSET2=0.5, gradient in 2-direction (beam\_offset\_gradient) | U2 = -1.000006E-01 | -5.000029E-02 | 1.000000E-02 | 5.000000E-03 |
| OFFSET1=0.5, gradient in 1-direction | U1 = -1.000006E-01 | -5.000029E-02 | 1.000000E-02 | 5.000000E-03 |
| OFFSET2=-0.5, gradient in 2-direction | U2 = 6.5E-15 | -5.000029E-02 | 1.000000E-02 | 1.500000E-02 |

Without offset the same beam gives -5.000029E-02 and 1.000000E-02, as expected. With OFFSET2=0.5 and a uniform temperature (`NALL, 10.`) the axial displacement is 1.000000E-02 = alpha T L, as expected.

## Where it goes wrong

Shells: gen3dfrom2d.f places the middle expanded node of a shell node at `co(j,nodes(2,k))=co(j,nodel(k))-thicks(k)*xnors(j,k)*offset(1,i)` (lines 183-184), i.e. at -e t from the reference surface. gen3dtemp.f gives the three expanded nodes:

```auto
              node=knor(indexk+1)
              t1(node)=t1(i)
     & -t1g(1,i)*thicke(1,indexe+j)*(0.5d0+offset(1,ielem))
              ...
              node=knor(indexk+2)
              t1(node)=t1(i)
              ...
              node=knor(indexk+3)
              t1(node)=t1(i)
     & +t1g(1,i)*thicke(1,indexe+j)*(0.5d0-offset(1,ielem))

```

(lines 215-224; the same for initial temperatures in lines 70-91). The outer nodes are right. The middle node gets the reference temperature t1(i), without the term `-t1g(1,i)*thicke(1,indexe+j)*offset(1,ielem)`. With OFFSET=0.5 and T = 0 the middle nodes get 0 instead of -5. Through the thickness the element then sees bottom T\_mid - g t/2, middle T\_mid + g e t, top T\_mid + g t/2; the quadratic interpolation through these has the mean T\_mid + (2/3) g e t.

Beams: gen3dfrom1d.f places the expanded nodes between -(0.5 + e1) t1 and +(0.5 - e1) t1 along n1 (and the same along n2), with the middle nodes at -e t (lines 80-227). For example, expanded node 4 lies at `+thickb(1,1)*xnorb(j,1)*(.5d0-offset(1,i))` `+thickb(2,1)*xnorb(j+3,1)*(.5d0-offset(2,i))` (lines 104-109). gen3dtemp.f gives it

```auto
              node=knor(indexk+4)
              t1(node)=t1(i)
     & +t1g(2,i)*thicke(1,indexe+j)*(0.5d0+offset(1,ielem))
     & +t1g(1,i)*thicke(2,indexe+j)*(0.5d0+offset(2,ielem))

```

(lines 242-245). The whole beam branch (lines 226-262, and 99-184 for initial temperatures) uses (0.5 + offset) on both sides of the section and has no offset term for the middle nodes. Across the section that gives T - g b (0.5 + e), T, T + g b (0.5 + e) at the bottom, middle and top: mean T, gradient (1 + 2 e) g.

## Fix

In gen3dtemp.f, give each expanded node the temperature at its actual position, as placed by gen3dfrom2d.f and gen3dfrom1d.f:

- shells: the middle node `t1(i)-t1g(1,i)*thicke(1,indexe+j)*offset(1,ielem)` (and the same with t0, t0g for the initial values);
- beams: (0.5 - offset) instead of (0.5 + offset) for the nodes on the positive side, and `-offset` for the middle nodes, in both directions. For example node 4: `t1(i)+t1g(2,i)*thicke(1,indexe+j)*(0.5d0-offset(1,ielem))+t1g(1,i)*thicke(2,indexe+j)*(0.5d0-offset(2,ielem))`.

Workaround: no offset where a temperature gradient is given (place the nodes on the mid-surface or centroid line and give the temperature there).

---

<div class="post-metadata">

**Author:** ![Calc\_em](https://avatars.discourse-cdn.com/v4/letter/c/43a26b/32.png) [@Calc\_em](https://calculix.discourse.group/u/Calc_em)\
**Post date:** [October 22, 2026, 9:02am UTC](https://calculix.discourse.group/t/offset-shells-and-beams-with-a-temperature-gradient-get-wrong-expanded-node-temperatures-wrong-thermal-expansion-and-beams-bend-1-2-offset-times-as-much/4212/2 "2026-10-22T09:02:56Z")

</div>

Confirmed using official build of ccx 2.23 on Windows, needs a GitHub ticket.

offset\_gradient.dat:

`5 -3.333333E-03 2.774961E-15 -1.000000E-01`

compared with:

> [@Sandervdb](#):
>
> Shells, node 5 (x = 2), g = 100, t = 0.1:
> 
> | OFFSET e | T | U1 ccx | U1 expected (alpha T\_mid x) | U1 error | (2/3) alpha g e t x | U3 |
> | --- | --- | --- | --- | --- | --- | --- |
> | 0.5 (offset\_gradient) | 0 | -3.333333E-03 | -1.000000E-02 (twin) | +6.667E-03 | 6.667E-03 | -1.000000E-01 |

---

<div class="post-metadata">

**Author:** ![Sandervdb](https://avatars.discourse-cdn.com/v4/letter/s/49beb7/32.png) [@Sandervdb](https://calculix.discourse.group/u/Sandervdb)\
**Post date:** [October 22, 2026, 11:18am UTC](https://calculix.discourse.group/t/offset-shells-and-beams-with-a-temperature-gradient-get-wrong-expanded-node-temperatures-wrong-thermal-expansion-and-beams-bend-1-2-offset-times-as-much/4212/3 "2026-10-22T11:18:34Z")

</div>

Posted: [OFFSET shells and beams with a temperature gradient get wrong expanded-node temperatures: wrong thermal expansion, and beams bend (1 + 2·OFFSET) times as much · Issue #261 · Dhondtguido/CalculiX · GitHub](https://github.com/Dhondtguido/CalculiX/issues/261)
