# Large rotation shell benchmark test

**URL:** <https://calculix.discourse.group/t/large-rotation-shell-benchmark-test/401>\
**Category:** Uncategorized\
**Created:** [January 11, 2021, 6:56pm UTC](https://calculix.discourse.group/t/large-rotation-shell-benchmark-test/401 "2021-01-11T18:56:30Z")\
**Posts on this page:** 10\
**Page:** 1

<div class="post-metadata">

**Author:** ![Uom0](https://avatars.discourse-cdn.com/v4/letter/u/8797f3/32.png) [@Uom0](https://calculix.discourse.group/u/Uom0)\
**Post date:** [January 11, 2021, 6:56pm UTC](https://calculix.discourse.group/t/large-rotation-shell-benchmark-test/401/1 "2021-01-11T18:56:31Z")

</div>

Highly motivated by [Capacity of beam calculation - #13 by Uom0](https://calculix.discourse.group/t/capacity-of-beam-calculation/387/13)  
I hereby try to test large rotation capabilities of calculix shell elements (to be expanded in solid ones) using a cantiliver beam as shown in the Figure,

 ![Untitled](https://global.discourse-cdn.com/free1/uploads/calculix/original/1X/501d16c6479af228d005062d9f4c1116c41c3355.png)

The applied moment M should equal 2 times PI, times the Bending stiffness over the length, i.e. M=2_PI_EI/L when the beam is completely rolled.  
I have created the following input file,

\*NODE, NSET=NALL  
1, 1, 0, 0  
2, 2, 0, 0  
3, 3, 0, 0  
4, 4, 0, 0  
5, 5, 0, 0  
6, 6, 0, 0  
7, 7, 0, 0  
8, 8, 0, 0  
9, 9, 0, 0  
10, 10, 0, 0  
11, 11, 0, 0  
12, 12, 0, 0  
13, 13, 0, 0  
14, 14, 0, 0  
15, 15, 0, 0  
16, 16, 0, 0  
17, 17, 0, 0  
18, 18, 0, 0  
19, 19, 0, 0  
20, 20, 0, 0  
21, 21, 0, 0  
22, 22, 0, 0  
23, 23, 0, 0  
24, 24, 0, 0  
25, 25, 0, 0  
26, 26, 0, 0  
27, 27, 0, 0  
28, 28, 0, 0  
29, 29, 0, 0  
30, 30, 0, 0  
31, 31, 0, 0  
32, 32, 0, 0  
33, 33, 0, 0  
34, 34, 0, 0  
35, 35, 0, 0  
36, 36, 0, 0  
37, 37, 0, 0  
38, 38, 0, 0  
39, 39, 0, 0  
40, 40, 0, 0  
41, 41, 0, 0  
42, 42, 0, 0  
43, 43, 0, 0  
44, 44, 0, 0  
45, 45, 0, 0  
46, 46, 0, 0  
47, 47, 0, 0  
48, 48, 0, 0  
49, 49, 0, 0  
50, 50, 0, 0  
51, 51, 0, 0  
52, 52, 0, 0  
53, 53, 0, 0  
54, 54, 0, 0  
55, 55, 0, 0  
56, 56, 0, 0  
57, 57, 0, 0  
58, 58, 0, 0  
59, 59, 0, 0  
60, 60, 0, 0  
61, 61, 0, 0  
62, 62, 0, 0  
63, 63, 0, 0  
64, 64, 0, 0  
65, 65, 0, 0  
66, 66, 0, 0  
67, 67, 0, 0  
68, 68, 0, 0  
69, 69, 0, 0  
70, 70, 0, 0  
71, 71, 0, 0  
72, 72, 0, 0  
73, 73, 0, 0  
74, 74, 0, 0  
75, 75, 0, 0  
76, 76, 0, 0  
77, 77, 0, 0  
78, 78, 0, 0  
79, 79, 0, 0  
80, 80, 0, 0  
81, 81, 0, 0  
82, 82, 0, 0  
83, 83, 0, 0  
84, 84, 0, 0  
85, 85, 0, 0  
86, 86, 0, 0  
87, 87, 0, 0  
88, 88, 0, 0  
89, 89, 0, 0  
90, 90, 0, 0  
91, 91, 0, 0  
92, 92, 0, 0  
93, 93, 0, 0  
94, 94, 0, 0  
95, 95, 0, 0  
96, 96, 0, 0  
97, 97, 0, 0  
98, 98, 0, 0  
99, 99, 0, 0  
100, 99, 1, 0  
101, 98, 1, 0  
102, 97, 1, 0  
103, 96, 1, 0  
104, 95, 1, 0  
105, 94, 1, 0  
106, 93, 1, 0  
107, 92, 1, 0  
108, 91, 1, 0  
109, 90, 1, 0  
110, 89, 1, 0  
111, 88, 1, 0  
112, 87, 1, 0  
113, 86, 1, 0  
114, 85, 1, 0  
115, 84, 1, 0  
116, 83, 1, 0  
117, 82, 1, 0  
118, 81, 1, 0  
119, 80, 1, 0  
120, 79, 1, 0  
121, 78, 1, 0  
122, 77, 1, 0  
123, 76, 1, 0  
124, 75, 1, 0  
125, 74, 1, 0  
126, 73, 1, 0  
127, 72, 1, 0  
128, 71, 1, 0  
129, 70, 1, 0  
130, 69, 1, 0  
131, 68, 1, 0  
132, 67, 1, 0  
133, 66, 1, 0  
134, 65, 1, 0  
135, 64, 1, 0  
136, 63, 1, 0  
137, 62, 1, 0  
138, 61, 1, 0  
139, 60, 1, 0  
140, 59, 1, 0  
141, 58, 1, 0  
142, 57, 1, 0  
143, 56, 1, 0  
144, 55, 1, 0  
145, 54, 1, 0  
146, 53, 1, 0  
147, 52, 1, 0  
148, 51, 1, 0  
149, 50, 1, 0  
150, 49, 1, 0  
151, 48, 1, 0  
152, 47, 1, 0  
153, 46, 1, 0  
154, 45, 1, 0  
155, 44, 1, 0  
156, 43, 1, 0  
157, 42, 1, 0  
158, 41, 1, 0  
159, 40, 1, 0  
160, 39, 1, 0  
161, 38, 1, 0  
162, 37, 1, 0  
163, 36, 1, 0  
164, 35, 1, 0  
165, 34, 1, 0  
166, 33, 1, 0  
167, 32, 1, 0  
168, 31, 1, 0  
169, 30, 1, 0  
170, 29, 1, 0  
171, 28, 1, 0  
172, 27, 1, 0  
173, 26, 1, 0  
174, 25, 1, 0  
175, 24, 1, 0  
176, 23, 1, 0  
177, 22, 1, 0  
178, 21, 1, 0  
179, 20, 1, 0  
180, 19, 1, 0  
181, 18, 1, 0  
182, 17, 1, 0  
183, 16, 1, 0  
184, 15, 1, 0  
185, 14, 1, 0  
186, 13, 1, 0  
187, 12, 1, 0  
188, 11, 1, 0  
189, 10, 1, 0  
190, 9, 1, 0  
191, 8, 1, 0  
192, 7, 1, 0  
193, 6, 1, 0  
194, 5, 1, 0  
195, 4, 1, 0  
196, 3, 1, 0  
197, 2, 1, 0  
198, 1, 1, 0  
199, 0, 1, 0  
200, 0, 0, 0  
201, 100, 0, 0  
202, 100, 1, 0  
\*\*\*\*\*\*\* E L E M E N T S \*\*\*\*\*\*\*\*\*\*\*\*\*  
\*ELEMENT, type=S4R, ELSET=EALL  
1, 202, 100, 99, 201  
2, 100, 101, 98, 99  
3, 101, 102, 97, 98  
4, 102, 103, 96, 97  
5, 103, 104, 95, 96  
6, 104, 105, 94, 95  
7, 105, 106, 93, 94  
8, 106, 107, 92, 93  
9, 107, 108, 91, 92  
10, 108, 109, 90, 91  
11, 109, 110, 89, 90  
12, 110, 111, 88, 89  
13, 111, 112, 87, 88  
14, 112, 113, 86, 87  
15, 113, 114, 85, 86  
16, 114, 115, 84, 85  
17, 115, 116, 83, 84  
18, 116, 117, 82, 83  
19, 117, 118, 81, 82  
20, 118, 119, 80, 81  
21, 119, 120, 79, 80  
22, 120, 121, 78, 79  
23, 121, 122, 77, 78  
24, 122, 123, 76, 77  
25, 123, 124, 75, 76  
26, 124, 125, 74, 75  
27, 125, 126, 73, 74  
28, 126, 127, 72, 73  
29, 127, 128, 71, 72  
30, 128, 129, 70, 71  
31, 129, 130, 69, 70  
32, 130, 131, 68, 69  
33, 131, 132, 67, 68  
34, 132, 133, 66, 67  
35, 133, 134, 65, 66  
36, 134, 135, 64, 65  
37, 135, 136, 63, 64  
38, 136, 137, 62, 63  
39, 137, 138, 61, 62  
40, 138, 139, 60, 61  
41, 139, 140, 59, 60  
42, 140, 141, 58, 59  
43, 141, 142, 57, 58  
44, 142, 143, 56, 57  
45, 143, 144, 55, 56  
46, 144, 145, 54, 55  
47, 145, 146, 53, 54  
48, 146, 147, 52, 53  
49, 147, 148, 51, 52  
50, 148, 149, 50, 51  
51, 149, 150, 49, 50  
52, 150, 151, 48, 49  
53, 151, 152, 47, 48  
54, 152, 153, 46, 47  
55, 153, 154, 45, 46  
56, 154, 155, 44, 45  
57, 155, 156, 43, 44  
58, 156, 157, 42, 43  
59, 157, 158, 41, 42  
60, 158, 159, 40, 41  
61, 159, 160, 39, 40  
62, 160, 161, 38, 39  
63, 161, 162, 37, 38  
64, 162, 163, 36, 37  
65, 163, 164, 35, 36  
66, 164, 165, 34, 35  
67, 165, 166, 33, 34  
68, 166, 167, 32, 33  
69, 167, 168, 31, 32  
70, 168, 169, 30, 31  
71, 169, 170, 29, 30  
72, 170, 171, 28, 29  
73, 171, 172, 27, 28  
74, 172, 173, 26, 27  
75, 173, 174, 25, 26  
76, 174, 175, 24, 25  
77, 175, 176, 23, 24  
78, 176, 177, 22, 23  
79, 177, 178, 21, 22  
80, 178, 179, 20, 21  
81, 179, 180, 19, 20  
82, 180, 181, 18, 19  
83, 181, 182, 17, 18  
84, 182, 183, 16, 17  
85, 183, 184, 15, 16  
86, 184, 185, 14, 15  
87, 185, 186, 13, 14  
88, 186, 187, 12, 13  
89, 187, 188, 11, 12  
90, 188, 189, 10, 11  
91, 189, 190, 9, 10  
92, 190, 191, 8, 9  
93, 191, 192, 7, 8  
94, 192, 193, 6, 7  
95, 193, 194, 5, 6  
96, 194, 195, 4, 5  
97, 195, 196, 3, 4  
98, 196, 197, 2, 3  
99, 197, 198, 1, 2  
100, 198, 199, 200, 1  
\*NSET,NSET=Nfixx  
1,  
2,  
\*MATERIAL,NAME=EL  
\*ELASTIC  
210000,.3  
\*SHELL SECTION,ELSET=EALL,MATERIAL=EL,OFFSET=0.  
1.0  
\*STEP, NLGEOM, inc=10000  
\*Static, direct  
0.00005, 1,  
\*BOUNDARY  
Nfixx,1,6  
\*CLOAD  
201,5,300  
202,5,300  
\*NODE PRINT,NSET=Nall  
U,RF  
\*EL PRINT,ELSET=Eall  
S  
\*NODE FILE,OUTPUT=3D  
U  
\*EL FILE  
\*END STEP

but I am still getting convergence issues and problems to get a completely rolled configuration.  
Can anyone take a look into this to suggest something else?.  
Cheers,  
/J.

---

<div class="post-metadata">

**Author:** ![vicmw](https://avatars.discourse-cdn.com/v4/letter/v/6de8d8/32.png) [@vicmw](https://calculix.discourse.group/u/vicmw)\
**Post date:** [January 11, 2021, 9:45pm UTC](https://calculix.discourse.group/t/large-rotation-shell-benchmark-test/401/2 "2021-01-11T21:45:34Z")

</div>

You’re not supposed to exceed 90 degrees with moment load on shells in static:

_[…] the user applied a rotation or a moment to a node.[…] in static calculations, starting with version 2.8 this type of loading is handled by using mean rotation MPC’s […] the rotation in a mean rotation MPC should not exceed 90 degrees._

Perhaps create a moment using opposing \*DLOADs on two surfaces at the tip of the strip. I’ve done a rolled strip like that before, but not sure if it was CCX shells or not.

---

<div class="post-metadata">

**Author:** ![Uom0](https://avatars.discourse-cdn.com/v4/letter/u/8797f3/32.png) [@Uom0](https://calculix.discourse.group/u/Uom0)\
**Post date:** [January 12, 2021, 8:55am UTC](https://calculix.discourse.group/t/large-rotation-shell-benchmark-test/401/3 "2021-01-12T08:55:13Z")

</div>

Right. Thanks for your response Victor @vicmw .

---

<div class="post-metadata">

**Author:** ![Disla](https://yyz2.discourse-cdn.com/free1/user_avatar/calculix.discourse.group/disla/32/3548_2.png) [@Disla](https://calculix.discourse.group/u/Disla)\
**Post date:** [March 18, 2024, 3:50pm UTC](https://calculix.discourse.group/t/large-rotation-shell-benchmark-test/401/4 "2024-03-18T15:50:50Z")

</div>

Solved. Hopefully this will not be a problem any more.

---

<div class="post-metadata">

**Author:** ![prop\_design](https://yyz2.discourse-cdn.com/free1/user_avatar/calculix.discourse.group/prop_design/32/197_2.png) [@prop\_design](https://calculix.discourse.group/u/prop_design)\
**Post date:** [March 18, 2024, 7:45pm UTC](https://calculix.discourse.group/t/large-rotation-shell-benchmark-test/401/5 "2024-03-18T19:45:08Z")

</div>

Besides the issues others have already pointed out…

When I experimented with this type of thing, Mecway and ccx did not have automatic remeshing. Moreover, when the elements become so distorted that they are no longer valid. Without that, I don’t think this capability very useful. It’s something that ANSYS has had for a long time. The software needs element criteria checks and the ability to automatically remesh, whenever, the criteria is not met. Even now, just doing a static mesh there are no checks.

---

<div class="post-metadata">

**Author:** ![Disla](https://yyz2.discourse-cdn.com/free1/user_avatar/calculix.discourse.group/disla/32/3548_2.png) [@Disla](https://calculix.discourse.group/u/Disla)\
**Post date:** [March 18, 2024, 8:14pm UTC](https://calculix.discourse.group/t/large-rotation-shell-benchmark-test/401/6 "2024-03-18T20:14:13Z")

</div>

This particular benchmark has analytical solution. It is provided considering a limited number of elements and specific material properties that makes the convergence itself a challenge.  
I will post the results to see how it compares with other commercial software.

---

<div class="post-metadata">

**Author:** ![Disla](https://yyz2.discourse-cdn.com/free1/user_avatar/calculix.discourse.group/disla/32/3548_2.png) [@Disla](https://calculix.discourse.group/u/Disla)\
**Post date:** [March 19, 2024, 5:29pm UTC](https://calculix.discourse.group/t/large-rotation-shell-benchmark-test/401/7 "2024-03-19T17:29:23Z")

</div>

Results. Unfortunately I haven’t found the way to impose the moment directly to the lip of the shell. Rotation driven and Moment is indirectly measured imposing both ends find at the base.

| | | | | | |
| --- | --- | --- | --- | --- | --- |
| L | 12 | m | | | |
| I | 8.33E-05 | m4 | | | |
| E | 1.20E+06 | Pa | | | |
| Mo | 8.33 | Nm | | | |
| Mmax | 52.360 | Nm | Expected | | |
| Mmax measured | 53.008 | | Measured | S4 | 16 Elements |
| Mmax measured | 38.252 | | Measured | S4R | 16 Elements |

![imagen](https://global.discourse-cdn.com/free1/uploads/calculix/original/2X/c/cc965cbec346a2a8c9cc2f429729bb6daafe2470.png)

 ![imagen](https://global.discourse-cdn.com/free1/uploads/calculix/original/2X/0/0a480ac3c817da78ea7ac9cfd8e2fb1bbff0d631.png)

---

<div class="post-metadata">

**Author:** ![xyont](https://yyz2.discourse-cdn.com/free1/user_avatar/calculix.discourse.group/xyont/32/3553_2.png) [@xyont](https://calculix.discourse.group/u/xyont)\
**Post date:** [March 20, 2024, 6:20am UTC](https://calculix.discourse.group/t/large-rotation-shell-benchmark-test/401/8 "2024-03-20T06:20:45Z")

</div>

model of solid element, deflections are true scale.

 ![2024-03-20 13_14_24-](https://global.discourse-cdn.com/free1/uploads/calculix/original/2X/4/4d4ec4494e435a55f3a216f93030d574a434b137.png)

 ![2024-03-20 13_13_44-](https://global.discourse-cdn.com/free1/uploads/calculix/original/2X/6/61916b6e2cdc606a1314a22bbe891263fdb123bc.png)

 ![2024-03-20 13_14_01-](https://global.discourse-cdn.com/free1/uploads/calculix/original/2X/7/751b6076d2d1748df18b68b39cbe62a8b3c3da80.png)

add higher rotation, it seems convergence is related to mesh.

 ![2024-03-20 13_30_04-](https://global.discourse-cdn.com/free1/uploads/calculix/original/2X/4/4a78c158076462e59ef3ccd8c9efe7e3ca856afe.png)

---

<div class="post-metadata">

**Author:** ![Disla](https://yyz2.discourse-cdn.com/free1/user_avatar/calculix.discourse.group/disla/32/3548_2.png) [@Disla](https://calculix.discourse.group/u/Disla)\
**Post date:** [March 20, 2024, 9:09am UTC](https://calculix.discourse.group/t/large-rotation-shell-benchmark-test/401/9 "2024-03-20T09:09:05Z")

</div>

Please try to adjust your contributions to the statement of the post.

SHELLS

---

<div class="post-metadata">

**Author:** ![xyont](https://yyz2.discourse-cdn.com/free1/user_avatar/calculix.discourse.group/xyont/32/3553_2.png) [@xyont](https://calculix.discourse.group/u/xyont)\
**Post date:** [March 20, 2024, 9:30am UTC](https://calculix.discourse.group/t/large-rotation-shell-benchmark-test/401/10 "2024-03-20T09:30:13Z")

</div>

however, no matter i modeling with shell or solid element, actually both are solid element in CalculiX except US3. But i’m still interested in what shell element models to be working for such cases.
